CrossFit Discussion Board  

Go Back   CrossFit Discussion Board > CrossFit Forum > Equipment
CrossFit Home Forum Site Rules CrossFit FAQ Search Today's Posts Mark Forums Read

Equipment Outfitting a serious gym. Vendors & suppliers. Devices & equipment

Reply
 
Thread Tools
Old 04-18-2010, 11:52 PM   #1
Dave G Clarke
Member Dave G Clarke is offline
 
Profile:
Join Date: Jul 2009
Location: Canberra  ACT Australia
Posts: 8
DIY bumper plates

Hi all,

I have a question which may well be met with horror and shock from many of you.

I have a cast iron or steel set of weights and barbell.

But I really like oly lifting.

As I canít afford a nice set of oly weights, I thought that I might get away with using two tires with plates attached to bring the bore of the hub down to the same as the barbell.

After a bit of googling, I found that others had already done the same:

http://www.straighttothebar.com/2007...bumper_pl.html


So I was quietly pleased with myself. However, in all the cases I found, I only saw tires on these peopleís barbells. As a single unit, a wheel and tire is not light. But when oly lifting, it isnít all that heavy, either.

How bad would it be to put my iron plates on the bar along with the tires? I was thinking that Iíd deflate the tires to that they were squishy but resilient, and maybe some rubber spacers between the iron plates to stop the banging against each other so hard.

Itís all very ghetto I know, but I just canít afford proper oly equipment for the time being.

Cheers,

Dave
  Reply With Quote
Old 04-20-2010, 10:31 AM   #2
Hugh Gilmore
Member Hugh Gilmore is offline
 
Profile:
Join Date: Jan 2008
Location: Kircubbin County Down  Ireland
Posts: 47
Re: DIY bumper plates

/expierimentation is the mother of knowledge .

Try it and let us know how you get on. the link you provided seems to be a good answer if you can finad a welder who will do it for you.


remember though if you are doing this to avoid spending money in the short term thats ok,

but i blew £800 a good bar an bumpers not because i could afford (still in Uni) it but because it was a lifetime investment, kind of like a house. if you are going to eventually want bumpers find a way to make it happpen it will cost less in the long run.

but also tyres look cool on a bar .

Last edited by Hugh Gilmore : 04-20-2010 at 10:35 AM. Reason: just
  Reply With Quote
Old 04-22-2010, 07:12 PM   #3
Gary Ohm
Member Gary Ohm is offline
 
Gary Ohm's Avatar
 
Profile:
Join Date: Jun 2008
Location: Paso Robles  Ca
Posts: 212
Re: DIY bumper plates

I've done this and mine are even more ghetto. I use trailer tires that are smaller than truck ones. I do put the iron plates on along with the tires. I only use 35# and 25# or smaller. I'm not strong enough to use more. My collars are super cheap two piece jobbers from the local sports store. The two pieces come apart and one part fits perfectly through the hole of the tire. THe halves of the collars screw together so it is all pretty stable. WAY cheaper than bumpers and plenty good for my cleans and snatches...
__________________
M/43/5'11.5625"/190/Paso Robles, Ca
  Reply With Quote
Reply


Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

vB code is On
Smilies are On
[IMG] code is Off
HTML code is Off
Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
DIY 5/8 lb fractional plates Seth Spritz Equipment 10 01-17-2010 09:01 PM
DIY Technique Plates David Gray Equipment 1 06-01-2009 02:21 PM
DIY Bumper Plate Rack Lei Fei Equipment 15 01-26-2009 10:09 PM
DIY: Fractional Plates Jerry Hill Equipment 11 08-22-2007 02:55 PM
Bumper plates and metal plates Daniel Morey Equipment 5 05-15-2007 07:04 AM


All times are GMT -7. The time now is 12:56 PM.


Powered by vBulletin® Version 3.6.8
Copyright ©2000 - 2020, Jelsoft Enterprises Ltd.
CrossFit is a registered trademark of CrossFit Inc.